Data Size Converter (KB, MB, GB, TB)
By TheToolsBank Editorial TeamLast updated:
Convert between bits, bytes, kilobytes, megabytes, gigabytes and terabytes instantly. This converter uses 1,024-based steps (1 GB = 1,024 MB), the way Windows reports file sizes, while drive makers sell capacity in 1,000-based decimal units. That gap is why a 1 TB drive shows as about 931 GB in Windows. The page also includes a SIEM EPS to GB-per-day calculator for sizing log storage.
Computer Storage Units Conversion Chart
The converter above works between bits, bytes, KB, MB, GB and TB in 1,024-based steps, so 1 KB = 1,024 bytes and 1 MB = 1,024 KB. Enter a number, pick the unit you have and the unit you want, then press Convert. The Swap button flips the two units, and the result also lists the value in every other unit. The chart in the next section compares those binary sizes with the decimal sizes used by drive makers and network providers.
Decimal vs Binary: Why 1 TB Shows as 931 GB
Drive makers count in powers of 1,000, so a '1 TB' drive holds 1,000,000,000,000 bytes. Windows counts in powers of 1,024, so the same drive is 1,000,000,000,000 ÷ 1,073,741,824 = about 931.3 GB (strictly GiB). No capacity is missing: the same bytes are just measured with a different divisor.
Data Storage Units Chart
| Unit | Decimal (SI) | Binary (IEC) |
|---|---|---|
| Kilobyte | 1 KB = 1,000 bytes | 1 KiB = 1,024 bytes |
| Megabyte | 1 MB = 1,000 KB | 1 MiB = 1,024 KiB |
| Gigabyte | 1 GB = 1,000 MB | 1 GiB = 1,024 MiB |
| Terabyte | 1 TB = 1,000 GB | 1 TiB = 1,024 GiB |
One byte is 8 bits. Need to shrink a file rather than measure it? See the Image Optimizer or check a document with the PDF Size Checker.
Mbps to MB/s: Data Transfer Rate Conversion
Network speeds are measured in bits and file sizes in bytes, and there are 8 bits in a byte. Divide Mbps by 8 to get MB/s: a 100 Mbps connection downloads at about 12.5 MB/s, so a 1 GB file takes about 80 seconds. Real downloads are usually a little slower because of network overhead.
| Connection speed | Transfer rate |
|---|---|
| 50 Mbps | 6.25 MB/s |
| 100 Mbps | 12.5 MB/s |
| 500 Mbps | 62.5 MB/s |
| 1 Gbps (1,000 Mbps) | 125 MB/s |
How to Convert SIEM EPS to GB per Day
To size SIEM log storage, multiply events per second (EPS) by the average event size in bytes and by the seconds in a day: GB/day = EPS × event size (bytes) × 86,400 ÷ 1,000,000,000. Example: 1,000 EPS × 500 bytes = 43.2 GB per day, or about 1.3 TB per 30 days before compression.
The SIEM calculator on this page does this for you: enter events per second, the average event size and your retention days to get GB per day and total storage.
Common Mistakes to Avoid
Confusing Mbps with MB/s.
Solution:
Network speed is in bits per second; file size is in bytes. Divide Mbps by 8 to get real MB/s throughput.
Assuming "GB" always means the same thing
Solution:
A manufacturer's GB (decimal) and your OS's GB (often actually binary GiB) can differ by roughly 7%, growing larger at bigger scales.
Ignoring filesystem overhead
Solution:
when storing large numbers of small files — actual disk usage runs higher than the simple sum of file sizes.
Sizing storage for today's needs only
Solution:
without planning for realistic data growth over the life of a project.
Forgetting RAID and backup overhead
Solution:
usable capacity after redundancy and backup copies is always less than raw purchased storage.
Frequently Asked Questions
Decimal (SI) units use base-10, so 1 KB = 1,000 bytes and 1 GB = 1,000,000,000 bytes; this is the standard used by hard drive manufacturers, network speed ratings, and most cloud providers. Binary (IEC) units use base-2, so 1 KiB = 1,024 bytes and 1 GiB = 1,073,741,824 bytes; this is the standard used internally by operating systems, RAM specifications, and file explorers.
Divide the Mbps value by 8, since 1 byte equals 8 bits. A 100 Mbps connection equals 12.5 MB/s of real throughput. To estimate transfer time, divide your file size in megabytes by that MB/s value to get seconds.
Manufacturers advertise capacity using decimal units, so a "1 TB" drive equals 1,000,000,000,000 bytes. Operating systems typically calculate and display storage using binary units internally, so that same drive appears as roughly 931 GiB. No capacity is missing — it's the same physical storage measured with a different divisor.
RAID 0 offers 100% usable capacity but no redundancy. RAID 1 (mirroring) gives roughly 50% usable capacity. RAID 5 gives (n−1)/n usable capacity across n drives. RAID 6 gives (n−2)/n usable capacity, trading some capacity for greater fault tolerance. The right choice depends on how much redundancy your use case requires.
It depends heavily on codec and resolution — compressed formats like H.264 4K use far less space per minute than high-bitrate formats like ProRes or RAW. Check your specific camera or software's documented bitrate, multiply by your expected shoot duration and shooting ratio, and add capacity for backups on top of that.

